Electronics Corp.

Make Your Own Printed Circuit Boards
Fast - Easy - Inexpensive!!!
 
CLOSEOUT SPECIALS

[ Home | Products & Services | Instruction Sheets | MSDS Sheets ]

[ Online Price Sheet | Tech Sheets ]

[ Order Form  | Frequently Asked Questions ]

Buy Direct From Us

Looking for those hard to find PC Boards? We have them cheaper than you can find elsewhere. If you see it cheaper, PLEASE give us a chance to beat that price for you. We have the widest variety of boards in the industry. If you don't see it, just ask. We have boards from .005" thick to double sided boards with 4 oz. of copper on each side.

Buy Your Photo Resist HERE !!

ONLY available at INJECTORALL

 

 

MATERIAL SAFETY DATA SHEET FOR CLEAR SPRAY 399E-16

 

PREPARATION DATE 02/06/96

EFFECTIVE DATE 02/09/96

 

HAZARDOUS INGREDIENTS

 

CHEMICAL NAME CAS NUMBER EXPOSURE LIMIT IN AIR            

Toluene                                                   108-88-3                             100 PPM ACGIH 200 PPM OSHA

1-Methoxy-2-Propanol Acetate    108-65-6                            NA PPM ACGIH NA PPM OSHA

Chlorodifluoromethane                           75-45-6                         1,000 PPM ACGIH NA PPM OSHA

 

PHYSICAL PROPERTIES

 

VAPOR DENSITY: (Air=1) > 2.98

EVAPORATION RATE: (NBTA=1) > 0.34

SPECIFIC GRAVITY: (g/ml) 1.02

BOILING POINT: 41.4 F

SOLUBILITY IN WATER: < 5 %

VAPOR PRESSURE: 20 C 57 psig

APPEARANCE: Clear liquid

ODCR Characteristic

 

FIRE AND EXPLOSION

 

FLAMMABLE LIMIT LEL >1.0

FLASH POINT: NA

(volume % in air) UEL <13.1

AUTOIGNITION POINT: NA

 

FIRE & EXPLOSION HAZARDS

This material is flammable and may be ignited by heat, sparks, flame or static electricity.

 

FIRE EXTINGUISHING MATERIALS

(1) Carbon Dioxide (2) Dry Chemical (3) Foam

 

SPECIAL FIREFIGHT'NG PROCEDURES

Self‑contained respiratory apparatus should be provided for firemen fighting in buildings or confined areas.

 

HAZARD RATING

 

FLAMMABILITY=MODERATE

HEALTH=SLIGHT  

REACTIVITY=INSIGNIFICANT

SPECIFIC=INSIGNIFICANT

 

HEALTH HAZARD INFORMATION

 

EYE: This material is an eye irritant. Direct contact with the liquid or exposure to vapors or mists may cause stinging, tearing, redness and swelling.

SKIN: Prolonged or repeated exposure may cause skin irritation. Repeated contact may cause drying or flaking of skin.

INHALED: Breathing high concentrations of vapors or mists may cause irritation of the nose and throat, signs of nervous system depression (e.g., drowsiness, dizziness, loss of coordination, and fatigue). Respiratory symptoms associated with pre-existing lung disorders (e.g., asthma-like conditions) may be aggravated by exposure to this material.

SWALLOWED: Unlikely route of exposure. Ingestion of excessive quantities may cause irritation of the

digestive tract. Signs of nervous system depression (e.g., drowsiness, dizziness, loss of coordination, and

fatigue).

 

EMERGENCY FIRST AID PROCESS

 

EYES: Irrigate immediately with water for at least 15 minutes. If irrigation or redness develops, seek immediate

medical attention.

 

SKIN: Immediately wash off attached area with large amount of water or with mild soap and water. Wash

contaminated clothing before reuse.

 

INGESTION: Call a physician or transport to emergency facility immediately.

 

INHALATION: Immediately move victim away from exposure and into fresh air.

 

The decision of whether to induce vomiting or not should be made by an attending physician. No specific

antidote. Treatment based on the judgment of the physician in response to reactions of the patient.

 

If victim is not breathing, artificial respiration should be administered by qualified personnel. If breathing

difficulties develop, oxygen should be administered by qualified personnel. Seek immediate medical attention.

 

REACTIVITY DATA

 

STABILITY: Stable

HAZARDOUS POLYMERIZATION: Will not occur

CONDITIONS: Do not store where temperature exceed 120 F. Avoid contact with aluminum and zinc and their

alloys, etc.

HAZARDOUS DECOMPOSITION: At very high temperatures, decomposes to carbon monoxide, carbon

dioxide.

 

SPILL, LEAK AND DISPOSAL PROCEDURES

 

SPILL RESPONSE PROCEDURES: Floor may be slippery, use care to avoid falling.

 

PREPARING WASTES FOR DISPOSAL: Replace cap and discard in trash. In compliance with local, state and federal regulations, dumping into sewers, or into any body of water is strongly discouraged. Do not incinerate or puncture.

 

SPECIAL HANDLING: DO NOT STORE ABOVE 120 F, OR 49 C. KEEP AWAY FROM STOVES, FURNACES AND DIRECT SUNLIGHT. DO NOT PUNCTURE OR INCINERATE. For brief contact/spray, no precautions other than clean body covering should be needed. TRAIN EMPLOYEES IN PROPER USE FOLLOW LABEL DIRECTIONS.

 

VENTILATION CONTROLS: Use the product in well ventilated area.

 

RESPIRATORY PROTECTION: Avoid prolonged exposure. Atmospheric level should be maintained below

 exposure guideline.

 

EYE PROTECTION: Safety goggles or face shield.

 

SKIN PROTECTION: Protective gloves, such as plyfluorinated or polyethylene or Vitron, and plastic aprons have been suggested.

 

LABELING: Provide ventilation. Avoid breathing of vapors. After use, be sure to wash hands. Keep out of reach of children. Do not spray onto open flame, hot surfaces that may become hot, such as light bulbs. Contents under pressure. Do not puncture or incinerate. Do not store at temperatures above 120 F (49 C). Intentional misuse by deliberately concentrating and inhaling vapor contents can be harmful or fatal. Avoid spraying into eyes.

 

DOT SHIPPING INFORMATION

 

PROPER SHIPPING NAME: Pressurized Aerosol Cans

HAZARD CLASS: ORM-D

ID NUMBER: None

LABEL REQUIREMENT: No Label Required

REPORTABLE QUANTITY: N/A

OTHER INFORMATION: Consumer Commodity

 

NOTICE

 

The information contained herein (including data and statements) is accurate as of the date hereof. Since the conditions of handling and use are beyond our control, we make no guarantee of results. We expressly disclaim any and all liability as to any of the product or such information, or recommendations.

 

[ Home | Products & Services | Instruction Sheets | MSDS Sheets ]

[ Online Price Sheet | Tech Sheets ]

[ Order Form | Frequently Asked Questions ]

Contact Information

Telephone

516-349-1273

FAX

631-563-3389

Postal address

40 Diamond Drive, Plainview NY 11803

 

 

Electronic mail

General Information: injectorall@mindspring.com

Copyright 2003 Injectorall Electronics Corp.

Hit Counter visitors to this page since Last Modified: June 22, 2001